Acier AISI M1 / 1.3346 / DIN S2-9-1
- Grade:
Cliquez pour envoyer un courriel Vendeur
Spécification, Chemical & Performance mécanique
Désignation par normes
Marque | Ravne No. | Tapis. Non. | DIN | EN | AISI |
BRM1 | 877 | 1.3346 | S2-9-1 | - | M1 |
Composition chimique (en% en poids)
C | Si | Mn | Cr | Mo | Ni | V | W | Autres |
0.82 | max. 0.45 | max. 0.40 | 3.85 | 8.60 | - | 1.15 | 1.75 | - |
Description
M1 is a molybdenum, chromium, vanadium alloy tool steel generally known as a Molybdenum High Speed Tool Steel. It is on of the most widely available tool steels in use today. It is similar in properties to the tungsten tool steels (T series) at a lower. Very tough high-speed Mo steel good grindability.
Applications
Twist drills, thread cutting tools, hobs and dies for broaching and cold flow pressing, cross recess dies for screw manufacture, cold rolling for e.g. Sendzimir equipment.
Propriétés physiques (valeurs moyennes) à température ambiante
Module d'élasticité [103 x N / mm2]: 217
Densité [g / cm3]: 8.0
Conductivité thermique [W / mK]: 19.0
Résistivité électrique [Ohm mm2/ m]: 0.60
Capacité thermique spécifique [J / gK]: 0.46
Coefficient de dilatation thermique linéaire 10-6oC-1
20-100oC | 20-200oC | 20-300oC | 20-400oC | 20-500oC | 20-600oC | 20-700oC |
11.0 | 11.5 | 11.9 | 12.3 | 12.4 | 12.5 | 12.5 |
Diagramme de transformation en refroidissement continu (CCT)
Cliquez sur l'image pour agrandir le diagramme.
Recuit doux
Chauffer à 820-850oC, cool slowly in furnace to 550oC then air. This will produce a maximum Brinell hardness of 262.
Stress Soulager
La décompression pour éliminer les contraintes d'usinage doit être effectuée par chauffage à 600-650oC, maintien pendant une heure à chaud, suivi d'un refroidissement par air. Cette opération est réalisée pour réduire la distorsion lors du traitement thermique.
durcissement
0 Harden from a temperature of 1180-1219oC followed by air or oil quenching or warm bath at 550oC. Hardness after quenching is 64-66 HRC.
Tempérer
Tempering temperature: 530 – 560oC, at least 2x for at least 63 HRC.
Diagramme de revenu
Cliquez sur l'image pour agrandir le diagramme.
Forger
Température de formage à chaud: 1100-900oC.
Cold Working
This alloy may be cold worked in the annealed condition.
Usinabilité
M1 is classified as a “medium” machinable alloy. Machining should be accomplished prior to hardening heat treatment followed by finish grinding. It has a rating of 50% that of the water hardening (W group) low alloy tool steels in regard to machinability.
Résistance à la corrosion
This is not a corrosion resistant alloy. In use as tooling it is often coated with oil to prevent rusting. A light film of oil. or protective wrapping, is essential to keep it free from corrosion.
Soudage
Consult the alloy supplier for information on weld procedures.
Formulaires fabriqués: veuillez consulter le programme de vente dimensionnel.